TM 9-2350-256-34-2Table 2-3. Troubleshaoting-ContinuedMALFUNCTIONTEST OR INSPECTIONCORRECTIVE ACTIONSPADE CIRCUIT (MAIN HYDRAULIC SYSTEM)-Continued23. SPADE WILL. OPERATE ONLY PARTIALLYStep 1. Test for improperly adjusted pilot operated relief and unloading valve. Install test gage in valve gage port.With engine operating at 1800 rpm, and spade in stowed position, place spade combination control valve leverin RAISE position and adjust relief valve.Adjust relief pressure to 1950-2050 psi. For location of valve gage port and adjusting screw, refer to views Band C, fig 3-22.Step 2. Inspect for loose spade cylinder attaching pins.a. Remove main winch and spade assembly. Refer to TM 9-2350-256-34-1, Medium Recovery Valve, M88A1.b. Repair or replace attaching pins. Refer to paragraph 3-6.Step 3. Inspect for galled spade pivot pins.a. Remove main winch and spade assembly, Refer to TM 9-2350-256-34-1, Medium Recovery Vehicle, M88A1.b. Replace spade pivot pins. Refer to paragraph 3-6.Step 4Damaged spade release valve.Replace spade release valve. Refer to TM 9-2350-256-20.HOISTING BOOM CIRCUIT (MAIN HYDRAULIC SYSTEM)24. BOOM WILL NOT OPERATEStep 1.Attempt operation of main winch. hoist winch and spade.If main winch. hoist winch and spade operate, proceed to step 13. If main winch. hoist winch and spade do notoperate. proceed with step 2.Step 2.Step 3.Step 4.Step 5.Inspect mechanical transmission drive shaft.If not rotating. repair or replace. Refer to TM 9-2350-256-34-1. Medium Recovery Vehicle. M88A1.Inspect mechanical transmission for broken or restricted hoses.Replace any broken or restricted hoses. Refer to TM 9-2350-256-20. Medium Recovery Vehicle. M88A1.Test for defective power control valve or restricted hose. Remove hose no. 66 from mechanical transmission.With mechanical transmission drive shaft rotating. and power control valve lever placed in ON position. oilshould flow from hose.a.Replace defective power control valve. Refer to TM 9-2350-256-34-1, Medium Recovery Vehicle, M88A1.b. Replace restricted or damaged hose. Refer to TM 9-2350-256-20. Medium Recovery Vehicle. M88A1.Inspect mechanical transmission output shaft. If not rotating. proceed with mechanical transmission clutchpressure check. Install pressure gage in mechanical transmission clutch pressure line. For location. refer to TM9-2350-256-20. Medium Recovery Vehicle. M88A1. With engine operating at 1800 rpm. and power control valvelever placed in OS position. normal operating pressure is 150 ± 10 psi.WARNINGTest components must be capable of withstanding a working pressure of 1950-2050 psi (step 6 only).NOTEAfter performing main hydraulic pump test. return all plumbing to original configuration.Step 6.Test main hydraulic pump. Remove check valve and tee between hose no. 4A and 4B. Install main hydraulicpump pressure tester kit (Item 14, Table 2-1) between hose no. 4A and hose no. 4B. Install test pressure gage intee.CAUTIONMake sure that the load valve is in full open position before performing test. When performing mainhydraulic pump pressure test, do not restrict oil flow beyond operating pressure.With main engine operating at 1800 rpm. operating pressure should be 1950-2050 psi when restricting flowusing load valve.After testing, remove hose no. 4B from pump port no. 1. Remove pilot-operated relief and unloading valveassembly from pump port no. 44. Install hose no. 4B on pump port no. 44.With main engine operating at 1800 rpm. operating pressure should be 1950-2050 psi when restricting flowusing load valve.a.Remove mechanical transmission and main hydraulic pump assembly. Refer to TM 9-2350-256-34-1, MediumRecovery Vehicle, M88A1.b. Replace main hydraulic pump. Refer to paragraph 3-16.Change 72-16.1
Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business
